Heel Blood Sampler Product Dimension Table
Product structure And Composition
The heel blood collector consists of shells, springs, blades and
elastic. The housing and elastomers are made of an
acrylonitrile-butadiene-styrene (ABS) material. The spring is made
of carbon spring steel wire; the blade is stainless steel.
Product Performance
- The appearance of the heel blood collector shall be clean without
obvious burrs, stains and defects; the leaves shall be free from
burrs and bending hooks.
- The heel blood collector is well assembled, with no significant
dislocation of the casing.
- The surface hardness of the blade shall not be less than 350HV10;
The blade surface roughness Ra value is not greater than 0.4 μM
- The corrosion resistance of the heel blood collector blade shall be
Grade B (with corrosion marks).
- The heel blood collector blade can be retracted with the blade in
the housing.
- The sterilization method is irradiation sterilization, and the
product should be sterile
- The heel blood collector blade shall be of no therogen reaction.
Specifications And Dimensions
| Size table of heel blood collector |
| Specification (mm) | Incision depth (mm) | Incision length (mm) |
| 0.85mm/1.75mm | 0.85mm±0.05 | 1.75mm±0.05 |
| 1.00mm/2.50mm | 1.00mm±0.05 | 2.50mm±0.05 |
Usage Method
1. lets the baby lie on his back, clean the blood collection parts
with disinfected cotton pieces, and dry naturally. Do not touch the
disinfected parts.
2. Remove the outer packaging of the blood collector. Do not place
the blood collector in unsterilized areas. Remove the safety buckle
of the blood collector. No
Do not touch the blade when the start button is pressed.
3. carries the baby's feet to a position above the heart, and
selects the safe blood collection position according to the "baby
blood collection location schematic diagram", and the blood
collection port is vertically aligned with the blood collection
position.
4. When the flat end of the blood collection outlet has mild
contact with the skin, press the start button to collect blood, and
the blood collector quickly leaves the blood collection point.
5. gently wipes off the first drop of blood with a dry sterile
gauze.
6.1 Press the appropriate pressure gently, and collect the
appropriate amount of blood sample with the blood collection tube
to collect blood. After the collection of blood, gently press the
incision with dry sterile gauze to prevent the formation of
hematoma.
6.2 Gently press the blood, directly sample the blood drops on the
blood card, and collect at least three blood points continuously.
After collecting blood, gently press the incision with dry sterile
gauze to stop the bleeding to prevent the formation of hematoma.
Contraindication
1. should not be used for infants (including fever) unless
absolutely necessary.
2. does not repeat collecting blood samples at the same location.
Do not use 3. puncture sites in infants with edema, infection, or
inflammation.
4. is not used at puncture sites for infants with skin disease or
skin damage.
5. avoids selecting skin within 2mm near the sampling point as the
blood collection location.
Matters Needing Attention
1. The safety belt buckle of blood sampler is lost or broken, so
please do not use it.
2. The blood sampler is disposable, so please replace it with a new
one every time you take blood.
3. The safe area for infant blood collection is between the line
parallel to the side of the foot drawn from the middle of the
fourth and fifth toes and the line parallel to the side of the foot
drawn from the big toe.
4. When the blood collection site is disinfected, the disinfection
diameter should be greater than 2cm.
5. Underdevelopment of blood vessels may lead to insufficient blood
flow.
6. If you need to preheat your heel, 42℃-44℃ will help promote
blood circulation, but over 44℃ will cause burns.
7. The blood sampler should be close to the blood collection site
and inserted into the needle vertically, but should not use too
much force to avoid causing deep and harmful wound depth.
8. When using the blood sampler, always be vigilant to avoid
accidental injury to yourself and others.
9. After blood collection, pay attention to the blood collection
place to prevent bleeding or inflammation again.
10. The blood sampler is sterilized by irradiation, and the
validity period is 3 years. Over the period of validity, is
strictly prohibited.
11. Blood sampler may be contagious after use, and shall not be
discarded at will to prevent pollution and injury.
Keep In Storage
It shall be stored in a cool, dry, well ventilated and clean
environment with relative humidity not more than 80% and
temperature not more than 45 ℃, without corrosive gas
Company profile
Zhongxiu Science And Technology Co.,Ltd., is a high-tech enterprise
engaged in the research and development, production and operation
of in vitro diagnostic products. The in vitro diagnostic products
developed by the company cover POCT series, microbial series,
biochemical series and immune series reagents and supporting
instruments.
The company has always adhered to the core concept of "fast and
accurate, living up to life", committed to providing society with
excellent products and services, and contributing to the cause of
human health.
